Technical Articles

By Karl Seelig, Vice President Technology and Tim O’Neill, Technical Marketing Manager

And why waiting until the last process step is a bad idea.

BTCs, or bottom termination components, are a class of package referred to by a variety of acronyms and abbreviations. Different component and packaging companies may use different nomenclature (FIGURE 1), but almost all these components share one common, ugly characteristic: large pads that are prone to solder voiding. By design, these large thermal or ground pads require a defined percentage of contact with the solder and PCB to properly conduct heat and/or electricity. Excess solder voids can impact performance and reliability of the package.

The voiding problem has given both designers and manufacturers heartburn for the...

By Karl Seelig, Vice President Technology, Tim O’Neill, Technical Marketing Manager and Mehran Maalekian, R&D Manager

Tin Whisker Study Conclusions.

Silver is a known whisker promoter but small amounts of bismuth mitigate the problem.  Alloy composition has a strong influence on tin whisker production and has proven to either mitigate or exacerbate the propensity for a solder to whisker. In our year-long study of the relationship between alloy composition on tin whisker formation, SAC 305 notoriously produced more and larger whiskers than any of the other alloys tested.

Sn0.6Ag0.6Cu3Bi, labeled “Alloy #69-2” in our test matrix, a tweak on one of the original nine alloys, produced the least and smallest whiskers. It also performed well in the other electronic solder suitability tests such as...

By Karl Seelig, Vice President Technology, Tim O’Neill, Technical Marketing Manager and Mehran Maalekian, R&D Manager

Phase 2 of our study involved wetting balance, spread, DSC and mechanical tests.

We’re continuing our summary of a year-long experiment aimed at identifying lead-free solder alloys that mitigate tin whisker growth. This study cut right to the chase, beginning with an elimination round. The first phase knocked out two-thirds of the nine original candidate alloys based on their whisker production.

The results of the tests were both intriguing and enlightening, and forced us to rethink what we thought we knew about tin whisker propagation. The investigation focused on the conventional wisdom that tin whiskers...

By Karl Seelig, Vice President Technology and Tim O’Neill, Technical Marketing Manager

Abstract. The drive to reduced size and increased functionality is a constant in the world of electronic devices. In order to achieve these goals, the industry has responded with ever-smaller devices and the equipment capable of handling these devices. The evolution of BGA packages and leadless devices is pushing existing technologies to the limit of current assembly techniques and materials.

As smaller components make their way into the mainstream PCB assembly market, PCB assemblers are reaching the limits of Type 3 solder paste, which is currently in use by most manufacturers.

The goal of this study is to determine the impact on solder volume deposition between Type 3, Type 4 and Type 5 SAC305...

By Karl Seelig, Vice President Technology and Tim O’Neill, Technical Marketing Manager

A multi-part study found plenty of whiskers, but not where they were expected.

 

THE ELUSIVE TIN WHISKER is only 1/100th the width of a human hair, but this tiny, single filament protrusion can wreak havoc with all sorts of electronics, and has even been cited as the cause of some sudden acceleration failures in cars. Tin whiskering is not a new phenomenon, however. It has been documented as far back as the 1940s, so why the heightened concern now? Lead was a great mitigator of whiskers and its removal from electronic solder opened the door for increased whisker proliferation, perhaps with sometimes deadly consequences.

Despite years of study, a single root-cause mechanism on...

By Karl Seelig, Vice President Technology and Tim O’Neill, Technical Marketing Manager

Before rejecting a flux, be sure you understand the standard.

J-STD-004 was updated about five years ago, but the comingling of designations from the old (A) and new (B) revisions in industry literature has created much confusion among users. What changed, what didn’t, how does it affect flux selection criteria, and what does a user need to know? Here’s a quick overview:

Flux designation has three components. The first two letters, RO, RE or OR, represent the basic chemical composition: rosin-based, resin-based or organic acid-based. Nothing has changed there. But the next component to flux designation, L, M or H, which describes the flux’s activity level as...

Rendimiento de la soldadura Sn/Cu/Ni a bajas temperaturas.

La soldadura de estaño-cobre modificada con níquel, conocida comercialmente como Sn100C®, es una aleación líder sin plomo para la soldadura PTH, el retrabajo y aire caliente nivelan los acabados finales de la PCB. Al no contener plata, es mucho más económica que las aleaciones SAC que contienen un 1, 3 o incluso un 4 por ciento del metal precioso, y produce uniones de soldadura suaves, brillantes y fáciles de inspeccionar. ¿Por qué no ha tenido una gran aceptación como una aleación SMT? En gran parte, por miedo. Miedo a la plena compatibilidad con los procesos de reflujo de SAC.

SnCuNi se funde a 227°C. SAC305 comienza a fundirse a 217°C, alcanzando su estado totalmente líquido a aproximadamente 220.6°C. Las temperaturas de reflujo recomendadas suelen ser al menos 13°C más altas que las temperaturas de...

By Karl Seelig, Vice President Technology, Tim O’Neill, Technical Marketing Manager, Kevin Pigeon and Mehran Maaleckian

ABSTRACT.  Low-silver and no-silver lead-free PCB solder alloys represent substantial cost savings over SAC alloys that contain 3% silver. Many wave solder operations use silver-free alloys for through hole soldering, and SMT operations are also beginning to adopt the alloy for surface mount soldering.

This paper reviews two case studies that test Ni-modified SnCu solder paste on mixed technology circuit assemblies which currently use SAC305 in production. The major differentiator between the two cases is the reflow profile: In one case, the SAC profile was considered nearly perfect for the SnCuNi alloy, peaking at 245°C. In the other case, thermally sensitive components constrained the profiles...

 

Cada experimentado ingeniero de procesos de SMT tiene al menos una historia de pesadilla sobre la mala química en el retrabajo. Ya sea que se trate de un flux incorrecto que se cuela en la operación, un flux insuficientemente procesado que queda en la tablilla o una eliminación inadecuada de residuos, todos corren el mismo riesgo: falla de campo. Si bien los operadores de retrabajo y los ingenieros de procesos rara vez tienen una idea del daño a largo plazo de materiales o procesos inapropiados, los ingenieros de análisis de fallas lo ven todo. Informan que la gran mayoría de los problemas relacionados con la soldadura están en juntas de soldadura retrabajadas, y la mayor parte de ellas se debe a la química de retrabajo.

¿Cómo logra llegar el flux incorrecto a la estación de retrabajo? Simple, error humano. En algunos casos, los operadores que experimentan dificultades al usar flux de...

By Karl Seelig, Vice President Technology and Tim O’Neill, Technical Marketing Manager

Introduction. As the proliferation of modern day electronics continues to drive miniaturization and functionality, electronic designers/assemblers face the issue of environmental exposure and uncommon applications never previously contemplated. 

This reality, coupled with the goal of reducing the environmental and health implications of the production and disposal of these devices, has forced manufacturers to reconsider the materials used in production.

Furthermore, the need to increase package density and reduce costs has led to the rapid deployment of leadless packages such as QFN, POP, LGA, and Micro-BGA. In many cases, the manufacturers of these devices will recommend the use of no clean...

Por Karl Seelig, Vice President Technology 

Abstracto.  En un esfuerzo por reducir las emisiones de compuestos orgánicos volátiles (VOC) en nuestro medio ambiente, los responsables de formular políticas han alentado y/o exigido que los fabricantes de productos electrónicos cambien del flux que contenga VOC a base de alcohol, a alternativas de flux libre de VOC a base de agua. Como resultado, el uso de flux libre de VOC está creciendo en América del Norte, Asia y Europa.

El propósito de este estudio es explicar varios...

By Karl Seelig, Vice President Technology

Abstract.  When lead-free solders were first introduced to the electronics industry in the early 1990’s, the tin-silver alloy composed of Sn96.5/3.5Ag was the first investigated. The most obvious difference from the industry standard was the substantially higher melting temperature of 221°C versus 183°C (Sn63/Pb37). 

Although Sn/Ag had been used extensively in hybrid electronics, concerns over silver migration and silver creep drove the industry to investigate Sn/...

By Karl Seelig, Vice President Technology and Kevin Pigeon, Senior Applications Manager

Introduction.  Over the last several years, the electronics assembly industry has witnessed a seismic shift toward component miniaturization. Consumer demands for more functionality in smaller packages have motivated OEMs and Contract Manufacturers to engage in new and innovative technologies. As technological advances usher in a more compact design, a decrease in available board space and more densely populated PCB’s have become increasingly common. In response to these demands, the industry has witnessed a proliferation of Quad Flat No Leads (QFN) packages. The goal of this study is to identify the advantages and challenges that the QFN package brings to the electronics assembly process. This...

Solder is a combination of metals that form an alloy with a melting point lower than any of the individual combined elements.

In the process of alloying, the metals are added and melted together and then cooled to a predetermined point above the melting point of the alloy. In the case of electronic-grade tin-lead (Sn63/Pb37) bar, this would be a point above 183°C (361°F) and for a leadfree alloy such as SAC305 (Sn96.5/Ag3.0/Cu0.5) it would be a point above 217-219°C (423-426°F). When an alloy is melted, the surface of the alloy is exposed to air. This interaction of the air on the alloy surface forms an oxide layer called dross. The density of the dross and the alloy are very similar, which causes a slow separation of the two. Typically, dross is not related to impurities but is more related to oxidation rates (although some impurities such as aluminum (Al) and zinc (Zn) do increase dross rates due to their rapid oxidation). Most impurities that are within the limits specified by...

By Karl Seelig, Vice President Technology and David SuraskiExecutive Vice President 

Abstract.  Since “nothing solders like solder”, HAL (Hot Air Leveling) will continue to hold a significant place in the surface finishing industry. Furthermore, the wave soldering process will continue to be a viable means of electronics assembly. However, as automatic soldering processes using lead-free alloys have become increasingly prevalent, questions have arisen about copper dissolution into these alloys.                 

...

By Karl Seelig, Vice President Technology and David SuraskiExecutive Vice President 

Abstract.  As the electronics industry begins to focus upon the tin-silver-copper family of alloys as a viable replacement for tin-lead solders, research needs to be done to determine if any particular alloy is best suited for the broadest range of applications. The tin-silver-copper family of alloys has earned a great deal of positive response from various industry consortia and organizations in recent years and the majority of manufacturers plan on implementing one of these alloys. However, as there are several different alloy formulations within the tin-silver-...

 

Discussion.  As lead-free wave soldering becomes increasingly prevalent, questions have arisen about copper dissolution into lead-free alloys. Concerns have arisen over the use of alloys that may require more solder pot maintenance due to their high copper dissolution rates. 

The first part of this study was performed to determine if there is any significant difference between Sn/Ag/Cu alloys. The study compared Sn/Ag3/Cu0.5 (LF218) to Sn/Ag2.5/Cu0.8/Sb0.5 (CASTIN). The purpose was to determine if at wave soldering temperatures one alloy will absorb less copper than the other alloy.

Test Procedure.  Two pots of each alloy holding approximately 500 grams of metal were heated to 530°F (276°C). Copper strips were weighed, fluxed and...

By Karl Seelig, Vice President Technology and David SuraskiExecutive Vice President 

Abstract. To successfully achieve lead-free electronics assembly, each participant in the manufacturing process, from purchasing to engineering to maintenance to Quality/Inspection, must have a solid understanding of the changes required of them. This pertains to considerations regarding design, components, PWBs, solder alloys, fluxe s, printing, reflow, wave soldering, rework, cleaning, equipment wear & tear and inspection.

Introduction.  With the WEEE and RoHS Directive in Europe (in its most recent revision) potentially outlawing...

Written By Karl Seelig, Vice President Technology

More complicated electronics will require the increased use of specialty solders. Specialty solders, such as indium alloys, offer advantages for gold soldering, step soldering and fatigue resistance.

Indium/Lead Solders on Gold.  Because they do not leach or dissolve gold as readily as tin/lead solders, indium/lead solders are recommended for soldering to gold.  As seen in fig. 1, the phase diagrams of tin/gold shows that tin dissolves approximately 18 percent by weight of gold at soldering temperatures of 225-250°C.1   Under the same conditions the indium/gold phase diagram shows dissolution of only 2 to 4 percent of gold in indium.  Thus, with a substantial reduction in the dissolution of gold, less...

By Karl Seelig, Vice President Technology

The increased interest in halogen-free assemblies is a result of Non-Government Organizations (NGOs) exerting pressure on electronic equipment manufacturers to eliminate halogens. The NGOs primary focus is on resolving global environmental issues and concerns. As a result of an increase in the enormous “e-waste” dump sites that have begun showing up around the world, NGOs are pushing consumer electronic manufacturers to ban halogen-containing material in order to produce “green” products. Not only are these sites enormous, but the recycling methods are archaic and sometimes even illegal. This stockpiling and dumping has created growing political and environmental issues. In order to deal with this issue, the question of why halogens are a focal point must be addressed.

As a safety measure halogens are added to...

Pages